HAMEG HM 208 PDF

Download HAMEG HM OSCILLOSCOPE UM service manual & repair info for electronics experts. Find great deals for HAMEG HM Oszilloskop 20mhz digital Storage. Shop with confidence on eBay!. I have been experiencing a problem with my Hameg HM oscilloscope. It was working correctly then the trace suddenly went back to the left.

Author: Shaktilmaran Zulkijar
Country: Cyprus
Language: English (Spanish)
Genre: Photos
Published (Last): 7 December 2009
Pages: 320
PDF File Size: 9.16 Mb
ePub File Size: 17.41 Mb
ISBN: 591-1-26375-134-1
Downloads: 94817
Price: Free* [*Free Regsitration Required]
Uploader: Dirn

Multiple flashing also applies with single sweep except the timebase stops after the single advance.

Select trigger coupling with TRIG, selector switch. Image not available Photos not available for this variation.

It must then be pushed in. In the case of a complaint, a label should be attached to the housing of the instrument which describes briefly the faults observed. The HM is easy to operate. Single channel display Y-section: The two stored signal waveforms must be output in two plotting processes in the dual mode. Its voltage rat- ing is max. Threshold, internal 5mm, external 50 mV.

However, some important differ- ences must be noted in the memory mode: However, the load on a supply could become open circuited on a defective unit causing the supply capacitors to remain charged. The timebase fine control knob is then out of operation. If the associated PLOT button is now depressed, hamsg penlift output is released, the pen of the XY plotter is applied with a slight delay and plotting starts.

HAMEG HM208 Oszilloskop 20mhz digital Storage

Amplitude variable control center pot. Using the 2 V CAL. Horizontal Deflection X Bandwidth: Starting with the vertical carrying position Fig. The DC position should only be used with a series-con- nected attenuator probe or at very low frequencies or if the measurement of the DC voltage content of the signal is absolutely necessary.

  EKTAGRAPHIC III KODAK MANUAL PDF

Oszillograph HM208

Learn More – opens in a new window or tab. BNC connector Input for external trigger source. The deflection in the memory mode is restricted in the X and Y direction to around 9 cm. A, B 2008 three positions for optinnum screen viewing Fig. An incorrect sequence when reading out from the memories has the effect in the display of Channel I that only half the information dot density is reproduced.

HAMEG HM Oszilloskop 20mhz digital Storage | eBay

It is only par- ticularly simple in this way. Practically every early failure is detected in intermittent operation by this. Then replace the fuse holder so that the impressed white triangle points to the desired mains voltage.

Full text of ” Hameg: Therefore the signal should in no case exceed 8 cm peak to peak on the screen. D27 Adjusting Plan A 1 Subject to change without notice 6. A capacitor of corresponding capaci- tance and voltage rating may be connected in series with the attenuator probe input for blocking DC voltage e.

Plug according to DIN5 pole. If the trace is hhm no longer visible after applying the signal voltage, it can be that the signal amplitude is much too large and totally overloads the vertical amplifier. Size of the signal voltage In general, AC voltage values normally refer to the rms value root means square value. X10 button not depressed the depressed button effects only the screen, not the plotter output.

Both memories are identical.

  A PERDIFIATO PDF

Fine control knob in the CAL. Subject to change without notice M17 – The 2. Learn More – opens in a new window or tab Any international shipping is paid in part to Hzmeg Bowes Inc. Phase difference measurement in DUAL mode A larger bameg difference between two input signals of the same frequency and shape can be measured very sim- ply on the screen in Dual mode DUAL button depressed. Non-destructive tests can be carried out on almost all semiconductors, resistors, capacitors, and coils.

In addition, the POS.

Hameg HM 2 Kanal Storage | eBay

Regulated DC power supplies: Calculation of the phase angle or the phase shift between the X and Y input voltages after measuring the distances a and b on the screen is quite simple with the following for- mula and a pocket calculator with trigonometric functions and besides independent of the sweep amplitudes on the screen. However, the visible signal on the screen can be expanded by pressing the X-MAG.

For sine wave hamge the upper limit is approx 30 MHz. The internal triggering is simultaneously switched over to Channel II with this button. WHD With lockable tilt handle Subject to change. Subject to change without notice M3 The measurement of the rise or fall time is not limited to the trace dimensions shown in the above 280. Operating modes of the vertical amplifiers The desired operating mode of the vertical amplifiers is selected with the 4 buttons in the Y field.